A Corrected Reading Written Over the First

A number is crossed out. The new reading is beside it. You run a finger along the smudge of pencil that edges the strike-through, confirming the original entry was not erased entirely per shop protocol. The initials of the quality tech who signed off on the correction sit half an inch below the new number, dated to 20 minutes before you sat down at the bench. You reach for your calipers to cross-reference the reading against the first piece sitting in your vise before you move to the production run.

This traveler outlines cross-check steps for adjusted measurements

All crossed-out entries on active job paperwork require three verifications before you proceed with production, to catch transcription errors or unapproved adjustments before they lead to scrapped parts. Follow these steps in order to validate the correction:

A Corrected Reading Written Over the First
Shop light on a closed folder.
  1. Match the signature beside the correction to the printed list of authorized quality staff posted above your bench.
  2. Confirm the corrected measurement falls within the material tolerance band listed later on the same page.
  3. Take three independent measurements of the marked first piece using a calibrated tool, and average the results to confirm alignment with the new entry.
  4. Sign and date the right margin of the correction line to confirm you completed all checks.

Illustrative example: If the crossed-out number reads 0.468 inch and the new number reads 0.472 inch, your three caliper measurements should return an average between 0.471 and 0.473 inch to count as a match. You do not need to reach out to the quality tech who made the correction unless your measurements fall outside that 0.001 inch variance range, as they already logged the reason for the adjustment in the digital shop floor log linked to the traveler’s ID number. The reason on file notes the original entry was a typo from the engineering team, who updated the CAD file last week to thicken the part’s outer wall for better impact resistance.

Cross-reference this cert’s material tolerance ranges before cutting stock

The cert is stapled to the back of the traveler, printed on light blue weighted paper, and lists the full yield and shear strength ranges for the 6061 aluminum stock you are using for this run. You flip to the back of the packet to confirm the corrected measurement does not push the part’s wall thickness below the minimum tolerance for the application, which would lead to premature failure under expected load. Note that the cert lists tolerance ranges specific to this heat lot of aluminum, which was cast three months prior and stored in the climate-controlled stock room until this week. You mark the tolerance line that aligns with the corrected measurement with a small dot of pencil so you can reference it quickly if you notice unusual warping during the milling process. If the tolerance range for the wall thickness is 0.465 to 0.475 inch, the corrected 0.472 inch reading falls well within that band, so you do not need to adjust your tool offsets to account for excess material removal. The cert also lists the proper feed rate for this specific lot of aluminum, which you cross-reference against your mill’s existing program to confirm no adjustments are needed there either.

Inspect this first piece against the corrected reading before running the full batch

The first piece is clamped in your vise right now, still dusted with fine aluminum shavings from the initial test cut the day shift tech completed before they noticed the measurement error in the original traveler entry. You set your digital calipers to zero on the reference gauge block sitting at the corner of your bench, then take three readings of the wall thickness at the top, middle, and bottom of the part’s outer edge. You jot the three readings down in the blank space below the correction on the traveler, then calculate the average to confirm it matches the new number within the allowed variance. You also run a finger along the cut edge to check for burrs that might skew your measurements, and use a deburring tool to smooth any rough spots before you take your final reading. If your average reading matches the corrected entry, you can adjust your mill’s program to use the new measurement as the target for the full run of 250 parts. You place the first piece in the labeled plastic bin at the end of your bench so the night shift quality team can pull it for random audit later in the week. You picked up the full packet, including the first piece, from the Traveler Desk on your way into the shop this morning, so you know all prior entries are logged and accounted for.

Pull this same sheet when you set up the second shift’s production run tomorrow

Tomorrow, you are responsible for setting up the second run of this part for the customer’s secondary order, so you will reference this marked traveler to confirm the correct measurement before you load new stock into the mill. You will not need to re-verify the correction at that point, since you already completed the cross-check steps today, but you will need to confirm the first piece of tomorrow’s run matches the same corrected measurement to account for any minor tool wear that happens between runs. You tuck the traveler into the top slot of the job folder sitting on your bench, so it stays with the first piece and the material cert until you pull it for tomorrow’s setup. You also make a small note in your personal digital shift log to reference this traveler’s ID number when you arrive tomorrow, so you do not mix it up with the three other aluminum milling jobs you have scheduled for the first half of your shift. If you notice any deviations in the stock’s tolerance tomorrow, you can cross-reference the marked correction against the digital log to confirm the adjustment reason, instead of waiting for a quality tech to come to your bench and re-approve the measurement. You also slip a small sticky note on the front of the job folder to remind yourself to check the tool’s wear level before you run the first test cut tomorrow, as small chips in the mill bit can lead to slight variations in wall thickness that fall right at the edge of the allowed tolerance range. You double-check that the cert is still stapled securely to the back of the traveler before you slide the folder into the slot for active jobs above your bench, so no loose pages get lost between shifts.

About · Contact · Privacy · Disclaimer · Advertising · Terms