Two First Pieces for One Operation

Two parts are marked as first. The sheet has one row. You slide the stack of raw bar stock off the left edge of your bench to set the paper flat, running a finger along the row’s entry for 304 stainless 2-inch round stock to confirm you pulled the correct lot this morning. The two blanks sit in the machinist’s vise next to your end mill, already faced and deburred, ready for the first of three contour cuts. You grab a fine-tip permanent marker from your apron pocket before you start reviewing the paper’s requirements.

First piece traveler validation steps

You work through this standard sequence before you run any cuts on either marked blank to avoid costly rework or wasted stock:

Two First Pieces for One Operation
Shop light on a closed folder.
  1. Cross-reference the operation number printed in the leftmost column of the traveler’s single row against the work order number taped to the front of your CNC machine to ensure you are running the correct job for the current shift. If the numbers do not match, return the traveler to the job file and pull the correct paperwork for the work you are scheduled to complete today.
  2. Confirm that the two pre-marked first piece blanks match the lot number printed in the third column of the traveler, with no extraneous stamp marks or surface pitting that would throw off dimensional readings after machining. If you notice any defects on the blanks, set them aside for scrap and pull two new blanks from the same lot to use as first pieces.
  3. Verify that the spindle speed, feed rate, and tool number listed in the traveler’s process notes match the values you programmed into the machine controller last night during setup. If any values do not align, adjust your program to match the traveler’s specifications before you proceed, or reach out to the process engineer if you believe the listed values will cause tool damage or part defects.
  4. Sign and date the top right corner of the traveler in the designated operator box before you run the first contour cut on either blank, writing your full employee ID number below your signature for tracking purposes.
  5. Place the signed traveler in the clear plastic sleeve mounted to the front of your machine so quality control can access it easily when they arrive to inspect the first pieces, no tucking it into a drawer or leaving it under a stack of tools where it cannot be found quickly.

Material cert cross-check for this run

You pull the folded material cert out of the back pocket of the traveler packet, unfolding it flat next to the page on your bench to avoid creasing or damaging the printed values. You match the heat number printed on the cert to the heat number stamped into the end of each first piece blank, as well as the heat number listed on the traveler’s single row, marking each match with a small dot from your permanent marker to track your progress. You note that the tensile strength and hardness values listed on the cert fall within the range specified on the traveler, no out-of-spec readings that would require you to pull a new lot of stock for this run. Illustrative example: if the cert lists a hardness of 82 HRB, that falls within the 75 to 85 HRB range noted for this part, so no further material testing is required before you proceed with machining the first pieces. You make a small check mark next to the heat number entry on the traveler to confirm you completed the cross-check, then tuck the cert back into the traveler’s rear pocket to keep it with the page for the full duration of the run, no separating the cert from the traveler at any point while the job is active.

Paired first piece dimensional sign-off

Once you run both first pieces through the full operation cycle, you set them on your granite surface plate next to a set of calibrated digital calipers, a height gauge, and a radius gauge to take all required measurements. You work through each dimensional callout on the traveler, measuring both pieces in the same order to avoid missing any critical features, including the 0.375 inch radius on the part’s lower edge, the ±0.001 inch tolerance on the 1.25 inch bore through the center, and the 0.002 inch maximum flatness allowance on the part’s top face. You record each measurement for both parts in the blank columns next to the dimensional callouts on the traveler, writing the exact value you read on your measurement tools with no rounding to make them fit within tolerance if you get a reading that falls outside the allowed range. If both pieces pass all dimensional checks, you call the quality control technician over to verify your readings and sign off on the traveler’s first piece approval line. If one or both pieces fail any check, you adjust the machine offsets as needed, run two new first piece blanks through the full operation cycle, and repeat the full measurement process before you request QC sign-off. You do not run any production parts until both first pieces are signed off on, and you keep the two approved first pieces in the labeled foam tray next to your machine for the full duration of the run to use as reference if you notice any dimensional drift in later production parts.

Next run startup you retrieve this same traveler

When you return to this operation for the next scheduled run, you pull this same traveler from the job file cabinet located at the Traveler Desk before you pull any raw stock or set up your machine for the run. You review the notes you added to the traveler during the previous run, including the offset adjustments you made after the first set of test parts and the measurement values you recorded for the approved first pieces, to cut down on setup time and avoid repeating the same small errors you encountered last time. You cross-reference the current lot of stock you plan to use for the new run against the material specifications listed on the old traveler to make sure you are using material that meets the same requirements, and you pull a new material cert for the current lot to tuck into the traveler’s rear pocket before you start prepping new first piece blanks. You keep the two original first pieces from the previous run on your bench while you set up the new run, using them to test fit the first new parts you machine to confirm your offsets are correct before you send new first pieces to QC for sign-off. You update all lot numbers, dates, and measurement values on the traveler for the new run, crossing out old entries with a single line so you have a full record of all runs tied to this operation for future reference. If you make any process adjustments during the new run that improve part quality or reduce cycle time, you add those notes to the blank space at the bottom of the traveler’s single row so the next operator to run this job can benefit from your changes.

About · Contact · Privacy · Disclaimer · Advertising · Terms